How to Make an RJ45 UTP Cable (Straight & Cross)

This time I repost from blogger friends who happened to be I want to know how to create / organize cables and RJ45 Straight Cable & Cross Order to be made ​​on a computer network terbuhung online to the internet / local. Than useful for me and you also want to learn to make their own lan network cable. Just follow the steps - steps below.

Before starting, of course we have to have a :

•      crimping pliers
•      UTP cable
•      RJ-45 connector
•      Cable Tester 
  
  
  Crimping pliers
  
  
  Tang krimping is a tool to cut UTP cable, and to clamp the end of the connector, and this is very
  important for us who want to learn how to mengkrimping cable, the tool shape is almost the same as regular tank that we see or meet. And below is a picture of crimping pliers:
  
  
  UTP cable
  
  

  UTP cable should we use for each channel the internet network, and in this UTP cable inside the cable there are 8 small pieces of colorful, color, and this small cable that is in the UTP cable:

  

  SEQUENCE SEQUENCE CABLE-UTP (Straight and Cross):
  Here is a sequence pengabelan Straight:

  

  A tip
      1. Orange and white
      2. Orange
      3. Green and white
      4. blue
      5. Blue and white
      6. green
      7. white Chocolate
      8. brown
  
  end of the B
  
      1. Orange and white
      2. Orange
      3. Green and white
      4. blue
      5. Blue and white
      6. green
      7. white Chocolate
      8. brown
  Here is a sequence pengabelan Cross:
  

  

  
  

    A tip
      1. Orange and white
      2. Orange
      3. Green and white
      4. blue
      5. Blue and white
      6. green
      7. white Chocolate
      8. brown
  
  end of the B
      1. Green and white
      2. green
      3. Orange and white
      4. blue
      5. Blue and white
      6. Orange
      7. white Chocolate
      8. brown
  
  Connectors
  Peripheral connectors is that we put on the end of the UTP cable to the cable goal can we put on the LAN port.
  

  

  
  We must have RJ-45 connector for UTP cable attached to the end. and is very useful tool.
  
  Cable Tester
  Cable Tester is a tool to test the results of our krimpingan (the cable crimping pliers) but if we are wrong then krimpingan Cable Tester lamp will not light up and if the results are correct then we krimpingan in Cable Tester lights will turn on automatically, so this is unbelievably useful tool for us to know krimpingan our results, below is an example image Cable Tester:
  

  
  

  Practice makes Straight Cable
  

  •  Peel the end of the UTP cable, approximately 2 cm
  •  Go to the torsion wire, straighten and cable urutankan standard TIA / EIA 368B
  •  Once the order is according to the standard, cut and flatten the end of the cable,
  •  Put the cable is straight and aligned into the RJ-45 connector, and make sure all the wiring position is correct.
  • Perform crimping using crimping tools, crimping tool and make sure the press and all the pins (brass) in the RJ-45 has "bite" of each wire.
  • When finished at the other end, do it again at the other end
  • The final step is the cable pulled the check you created earlier using the LAN tester, how to input each end of the cable (RJ-45) to masing2 port available on the LAN tester, turn and make sure all the LED lights in the order cable that we make.
  • Below is an example of the end of UTP cable that has RJ-45 connector is installed properly, the cable sheath (blue) come into the connector, cable order from left to right (in the picture below pin wiring sequence starting from top to bottom).
    
    May be useful